Stamford Roof Pros provides professional fascia and soffit in Stamford, CT for residential and commercial properties across lower Fairfield County. Eaves rot from the top down and the inside out, so by the time paint fails on a fascia board the rafter tail behind it is usually going too. On the older housing here that is the most common carpentry item attached to a roof job.
The causes are unglamorous and repeat. Ice dams backing water behind the gutter every February, gutters left full so the trough overflows against the board, a drip edge that was omitted or is too short to carry water past the fascia, and paint that has not been renewed since the house last changed hands. Any two of those together will take out a board in a decade.
Doing it properly means cutting back to sound wood. We remove the gutter, open the eave, cut rotted rafter tails square and sister new material past the wall line, replace the sub-fascia, then run cellular PVC or primed cedar and prime every cut end including the backs. Wrapping aluminum over a wet, punky board hides the problem for exactly as long as it takes to sell the house.
The soffit is not decoration. On a vented attic it is the whole intake side of the system, so a solid soffit, a painted-over perforated panel or an insulation-packed bay means the ridge vent above is pulling air out of the house. We open the intake back up whenever the eave is apart. An attic that finally breathes stops icing the eave that rotted.
On the commercial side the word means something else entirely. There the fascia is the perimeter edge metal, a tested wind-rated assembly on a continuous cleat that holds the membrane down at the most highly loaded part of the roof. It is structural, not trim, and it gets replaced as a rated system rather than patched with a screw and a bead of sealant. Refastening failed edge metal buys a season at most.
One honest note on sequencing. If a roof is coming off next spring, do not repair the fascia this autumn. The eave is easier, cheaper and better done with the shingles off and the drip edge already up, and doing it twice costs you the labor twice. We will tell you to wait. It is one of the few times we will ask you to hold off on spending money with us.
Our licensed and insured team brings the right materials and equipment to every job — hot-air welded 80 mil TPO and PVC single ply, tapered polyisocyanurate board over a steel deck, ANSI/SPRI ES-1 rated perimeter edge metal, self-adhering polymer-modified bitumen ice barrier, laminated architectural shingles rated to ASTM D3462, high-density cover board between insulation and membrane — and backs the work with a written workmanship warranty. We serve Stamford and nearby communities including Greenwich, Cos Cob, Riverside, Old Greenwich.
What We Handle
Everything our fascia and soffit in Stamford covers
One crew, one point of contact, and the full range of fascia and soffit work in Stamford, CT. If it is on this list we do it in house rather than handing it to a subcontractor:
- fascia repair stamford ct
- soffit replacement stamford connecticut
- rotted fascia board fairfield county
- rafter tail repair stamford
- pvc fascia stamford ct
- vented soffit installation stamford
- eave rot repair stamford
- aluminum wrap fascia stamford connecticut
- drip edge installation stamford
- commercial roof edge metal stamford
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Stamford services.
Materials, equipment and how we do fascia and soffit
The difference between fascia and soffit that lasts and fascia and soffit that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with hot-air welded 80 mil TPO and PVC single ply, tapered polyisocyanurate board over a steel deck, ANSI/SPRI ES-1 rated perimeter edge metal, self-adhering polymer-modified bitumen ice barrier, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Stamford job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of roofing work in lower Fairfield County means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do fascia and soffit outside Stamford
Stamford Roof Pros covers Stamford and the surrounding communities of lower Fairfield County. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Fascia and Soffit in Greenwich, CT — Fairfield County, population 63,518
- Fascia and Soffit in Cos Cob, CT — Fairfield County, population 6,873
- Fascia and Soffit in Riverside, CT — Fairfield County, population 8,843
- Fascia and Soffit in Old Greenwich, CT — Fairfield County, population 6,962
- Fascia and Soffit in Byram, CT — Fairfield County, population 4,493
- Fascia and Soffit in Glenville, CT — Fairfield County, population 2,762
Start on the Stamford Roof Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Stamford Chooses Stamford Roof Pros
- ✓We tell you which side of Connecticut's six-unit line your building falls on before we quote it, because it decides your contract terms, your cancellation rights and what recourse you actually have.
- ✓Ask any roofer here for a registration number. The statute requires it in advertising and on the contract, and a home improvement contract missing it is not enforceable against you.
- ✓Commercial membrane is our weekday work, not a sideline. That is why the flashing and drainage detailing on our shingle jobs looks the way it does.
- ✓We take core cuts before recommending a coating or a recover, and we hand you the wet insulation rather than describing it in a proposal.
The standards behind fascia and soffit
Quality here is not a matter of opinion — it is written down. The fascia and soffit work we do in Stamford follows published industry standards: NRCA publishes the Roofing Manual, the industry's reference for details and slope minimums, and Asphalt Roofing Manufacturers Association sets the shingle application and ventilation guidance the warranties reference. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every fascia and soffit project in Stamford gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free fascia and soffit free estimate in Stamford, or request a quote and we'll get right back to you.